- Air Cleaners, Scoops & Oil Filters (71)
-
Visit our Ebay store
for more products
-
Visit Calvert Racing Suspensions
for more products
-
MSD-8987 MSD Start and Step Timing Control Digitally Controlled
$260.00
-
NPT Pipe Reducer 1/8" to 1/4"
Blue Finish$9.65
-
90° Tube to Male AN Adapter 5/16"to -6AN
Blue/Red Finish. Suits Aeroflow, Moroso & Russell Tubing$34.97
-
Stainless Steel Banjo with Double AN Fitting
10mm (3/8") Double Ended Banjo to -3AN Male$27.81
-
510 Series Full Flow Tight Radius Push Lock 180° Hose End -10AN
Blue Finish. Suit 400 Series Hose$32.00
-
570 Series One-Piece Full Flow 180° Hose End -16AN
Black Finish. Suit 200 Series PTFE Hose$51.57
-
ARP-235-2501 Harmonic Balancer Bolt, Chromoly, Black Oxide, 12-Point, Chevy, Big Block, Each
$53.00
-
90° Full Flow Female/Male Flare Swivel -12AN
Blue$40.39
-
HOLLEY 110 GPH MECHANICAL FUEL PUMP
$202.00
-
Stainless Steel 2 into 1 Merge Collectors
2-1/2" Primary Into 3-1/2" Collector Outlet$0.00
-
Visit our Ebay store
for more products
-
AEROFLOW Billet Power Steering Bracket.Suit S/B Chevy,Passenger Side High Mount P/S Pump,With Long Water Pump.(Polished or Black)
$0.00
-
Stainless T-Bolt Hose Clamp 98-103mm
$8.69
-
HOLLEY REPLACEMENT FUEL BOWL KIT
$109.00
-
100 Series Stainless Steel Braided Hose -12AN - Black
15 Metre Length$580.69
-
ARP Valve Cover Bolts S/Steel Hex 1/4"-20, Chev Center bolt Stamped Steel Covers Set Of 8
$36.00
-
500 Series Cutter Swivel 120° Hose End -20AN
Blue/Red Finish. Suits 100 & 450 Series Hose$71.14
-
Strange Double Externally Adjustable Aluminum Coil Over Shocks 15.40''EXT 10.76''Collapsed Bearing to Bearing Ends Come With Springs Pair
$1,148.40
-
Billet Aluminium P-Clamp 7/16" (11.1mm)
Suit -4 Braid & -6 PTFE Hose, Red Finish$5.46
-
RACE STAR 92-510152DP DRAG STAR 15" X 10", 5 X 4.50" BC, 6.25" BS, FORD, CHRYSLER (POLISHED)
$293.00
-
10" Electric Thermo Fan
Curved Blades$58.42
- No News
Wire Mesh Carburetor Screen for Dragsters
Our customer is a Champion Super Street Drag Racer and he asked us to develop a stainless steel wire mesh carburetor screen to cover the carburetor on his drag car.
Customer Requirements
The proper design for the carburetor screen needed to have mesh fine enough to keep out small stones, tools and rags, but be open enough to allow maximum air flow. The screen had fit snuggly on the face of the carburetor so it wouldn’t rattle at high RPMs. And it needed several grommeted holes for the hold down post and carburetor float vent tubes.
Our Solution
The Carburetor Screen we developed for our customer uses 6 mesh x 0.028″ woven wire mesh which has a 0.138″ opening and a 69% open space. Grommets are installed in several holes and the mesh is formed into a shallow bowl shape in a hydraulic press. Then a stainless steel band is welded to the bottom edge.